Cisco 300-110 Exam Overview:

Cisco 300-110 Exam Syllabus Topics:

Cisco Designing Cisco Wireless Networks Sample Questions:

1. An engineer must assess an existing company WLAN to determine the possibility for future IEEE
802.11ac Wave 2 wireless deployment. All access switches are Fast Ethernet-capable only, and the wired infrastructure between existing APs and access switches is based on the CAT 6A standard. Which two actions provide maximum support of Cisco 3800 Series access points?
(Choose two.)

A) Replace the existing switches with gigabit switches with 10G uplinks.
B) Ensure that cable distances between access switches and APs are not longer than 100 meters.
C) Replace the existing switches with mGig switches.
D) Replace the existing wiring infrastructure with the CAT-7E wiring standard.
E) Ensure that cable distances between access switches and APs are not longer than 55 meters.

2. A university has three campus locations and the main data center. Each campus location has a Cisco Catalyst 9800-40 WLC that manages 600 APs. The data center has a Catalyst 9800-40 WLC, which serves as N+1 backup for each campus WLC. A consulting engineer must install four additional Catalyst 9800-40 WLCs to serve as high availability SSO pairs for each campus, but only two have been approved due to budget restrictions. Requirements: Data center WLC must always be available as N+1 backup, Campus1 WLC must operate with zero downtime, and in the event of multiple campus outages, the AP priority order is to support Campus3, Campus2, then Campus1. Which design approach must the consulting engineer take?

A) The data center WLC and Campus1 WLC are the high availability SSO pair. Campus3 APs have priority 4, Campus2 APs have priority 2, and Campus1 APs have priority 1.
B) The data center WLC and Campus1 WLC are the high availability SSO pair. Campus1 APs have priority 4, Campus2 APs have priority 2, and Campus3 APs have priority 1.
C) The data center WLC and Campus3 WLC are the high availability SSO pair. Campus3 APs have priority 4, Campus2 APs have priority 2, and Campus1 APs have priority 1.
D) The data center WLC and Campus3 WLC are the high availability SSO pair. Campus1 APs have priority 4, Campus2 APs have priority 2, and Campus3 APs have priority 1.

3. An engineer is designing a point-to-point outdoor bridge link spanning 4 km between two buildings. Which two factors must be calculated during the design? (Choose two.)

A) CAPWAP control plane MTU
B) link budget including antenna gain, cable loss, and receiver sensitivity
C) DHCP scope size at the remote building
D) 60% Fresnel zone clearance along the path
E) mobility group name consistency at both ends

4. A customer is migrating from a legacy Cisco AireOS WLC to a new Cisco 9800 IOS XE WLC with Cisco 9100 APs. The new APs must associate to the Catalyst 9800 WLC, and wireless clients must seamlessly roam between the old and new WLCs even during SSO. The new Catalyst 9800 WLC deployment is configured to use SSO. Which command must be added to meet the requirements?

A) C9800# chassis redundancy ha-interface local-ip <local IP> subnet <local IP subnet> remoteip
<remote>
B) C9800# wireless mobility mac-address <MAC>
C) C9800(config)# management gateway-failover enable
D) C9800(config)# ip default-gateway <IP>

5. A university lecture hall has a Cisco wireless high-density network with this configuration: ?5 GHz only ?20-MHz channels ?UNII-1, UNII-2, and UNII-2E channels ?TPC minimum = 8 ?TPC maximum = 14 The lecture hall is 200 feet by 100 feet and has 16 Cisco APs that use directional antennas. Which feature must be included in the design to mitigate and reduce high-channel utilization from rogue APs?

A) 802.11w
B) band select
C) DFS detection
D) RxSOP

Solutions: